Hot 35MHz-4000MHz RF Signal Generator Signal Source ADF4351 VFO HXY D6 V1.02 US

Description

Product Description
Supply voltage: DC 4.5V-5.5V
Standby current: <25mA
Emission current: <150mA
Output impedance: 50 ohms
Output frequency range: 35MHz-4000MHz
Output stepping: 1KHz-8KHz
Output power: -1dBm (W) @ 150MHZ (test power absolute value) about 1 mW
Features:
Simple RF signal source signal generator
Core components: avr mega8 microcontroller, cost-effective single-chip, is a low-profile version of the commonly used m16. There is a 2.56v regulated source in the peripheral ADC, which is not available in other mid-range microcontrollers.
Adf4351: Traditional VCO+PLL+6 series high speed bistable circuit. The output is obtained by frequency division, and the output is a square wave. The amplitude of the fundamental wave does not change much.
This product uses the single-chip microcomputer as the core, which greatly simplifies the design, shortens the development time and saves the cost. It provides the signal source for the AC channel of the device under test and analyzes the frequency-amplitude characteristics of the AC channel. Please pay attention to the impedance of the measuring device.
More Details:
This product operation keyboard has 15 ppt keys, 0~9 number keys, 10, "++" and "--" keys to adjust the frequency to use, also produces emission output behavior, short press "++" or "-- ”Key stepping adds 1khz or minus 1khz to the original frequency output. Pressing “++” or “--” for more than 1 second will result in a continuous or continuous subtraction scan mode. The step is 1khz at 35mhz~138mhz; 138mhz The step is 10khz at ~550mhz and 100khz at 550mhz~4000mhz. To end the scan, simply press the "++" "--" button or the "ok" button. The “ok” button is the output control button. Press it to launch. Press again to stop the transmission. The emission behavior caused by “++” or “--” needs to press “OK” twice to end the transmission. This product will display “>>” in the upper right corner of the display when there is output emission behavior. The “C” key will end the transmission and the frequency will be zero.
Stepping "< >" key, used for continuous plus continuous subtraction scan mode for easy adjustment, cycle selection step "1K", "10K", "100K", "1M", although not very useful, but also small Improvement, the original V1.01 board as long as the keyboard on the hole welding a 3.3k resistor and a PPT touch button to complete the improvement (compared to the keyboard board diagram, very simple), then, buy an AVR ISP download on Taobao The line downloads the bottom layer of the new MCU, and there is a new underlying source code and .hex file in the network disk. The fuse bit C9EF is not wrong.
The new bottom layer LCD1602 power-up defaults to the "<1k>" stepping indication by pressing the "<>" button. There are four types of stepping states that can be cycled.
Package Included:
1 x Simple RF Source Generator
Note: Please note that this machine does not have built-in voltage regulator unit, please keep it within the voltage range. Thank you!
Payment
1
. We accept Paypal only.
2
. We only ship to your Paypal's address, please ensure your shipping address on your paypal account is correct. If you have any change for address, please inform us in ebay note.
3
. Payment must be fulfilled within 7 days after purchase. All non-paying orders will receive an unpaid reminder from eBay.
Shipping
Once we have received cleared full payment, your items will be dispatched in 1-3 days.
It normally takes :
5-10 business days
for US
if your shipment delays, we hope you can be patient, please don't open dispute and at the same time contact us, we will try our best to help you.
In addition, we have 2 warehouses in the United States. We will delivery the items according to the order address and our inventory in each warehouse.
Returns
If any item is defective upon receipt or do not work, please contact us for the return address, return is accepted within 30 days after the buyer receiving the item.
Returned item has to be in its original condition. Buyer is responsible for return shipping costs . After receiving the return we will make a replacement depends on our available stock, if not available, a refund will be issued.
Feedback
1. In order to provide you the best service please treat the transaction fairly. Feedback is our life, before you leave a neutral or negative feedback, please DO contact us to get a better solution, Because we don't want to get a NEUTRUAL feedback or NEGATIVE feedback .
2. If you are satisfied with our products and service, please help to leave "Positive Feedback" and "5 Perfect Stars”,for us when you receive your items and we will do the same for you. Thanks in advance!
3. If you have any questions regarding the transaction, before leaving any feedbacks, please contact us and give us an opportunity to find a solution. Thank you!
powered by